From the experts at Arnott

As an aftermarket air suspension specialist, Arnott says it is keen to make sure all installers feel confident and are well informed when carrying out an air suspension repair. In this article, its experts share some valuable tips and tricks.

Air springs
After installing an air spring, always make sure to double check that the lower piston is mounted correctly and seated/engaged in its mounting pins/locks. Otherwise, the lower piston can break, or the air spring can dislodge from its location.
Make sure the air line is properly placed and routed. Improper air line installation can cause the air line to get stuck between the air spring and chassis components (for example, the inner wheel housing), making it impossible to deflate the air spring through the air line.
Always inflate the air spring whilst supporting the vehicle. If neglected the vehicle weight is unevenly distributed. Consequently, the air spring can bend during the air up procedure. This puts so much stress on the air sleeve that it could cause the bladder to be pulled out of the crimping ring.
When replacing an air spring, always make sure to thoroughly check the shock absorber as well. Be aware that the shock absorber is responsible for damping, not the air spring. When the damping force of the shock absorber is no longer sufficient, the air spring needs to absorb more of the impacts which is something it is not made for. This can cause the lower piston to crack or break off.

Air struts
When installing the air line on an Arnott part, it is almost never necessary to remove or tighten the fitting. If removed, Arnott recommends tightening the Voss fitting with maximum 2Nm. When more torque is used, it can damage the screw-thread which will lead to the air spring leaking air on the fitting.
After installation, check if the wiring/connectors are positioned properly. Improper installation or loose connections can generate fault codes. Tighten the top bolts with care and according to manufacturer’s specification. In general, Arnott would not recommend the use of pneumatic tools for this. Overtightening the bolts can damage the thread, or it can even break off. Arnott delivers its air struts with the proper mounting nuts and bolts and asks that you please use those to facilitate a smooth and easy installation.

Compressors
Compressor burn-out or overload is often a consequential damage which makes it crucial to check the air suspension system for possible leaks. Usually, it is easy to recognise if a compressor failed due to burn-out/overload because it smells burnt, the compressor labels have turned yellow due to the extensive heat and often the lines/connectors are partially melted as well. If this is the case, do not just install a new compressor but make sure to find the root cause. Otherwise, the new compressor will likely become defective in no time as well.
When replacing a compressor always replace the relay as well and check or replace the air filter. The compressor is switched on and off by a relay that is controlled by the Electronic Control Unit (ECU). The relay can get sticky causing the compressor to continuously pump air. This will eventually lead to a burned-out compressor. The compressor sucks and ventilates air through its air filter. If the old compressor broke down due to water and/or dirt inside, it is likely that the air filter is contaminated. If only a new compressor is replaced in such case, the new compressor will suck in the existing water/debris.
After replacing the compressor, always check the condition of the inlet and intake hoses. An intake hose can dry out and become porous causing leakage and/or they break off from the compressor. In both situations this leads to water and dirt inside the compressor causing it to break down. If left unnoticed, it will also damage the new compressor beyond repair. And don’t forget to check the wiring loom of the compressor for possible broken or cracked wires. A compressor can vibrate when in operation, causing the wiring to wear out.

Arnott products
With more than 30 years of experience in engineering, designing, and manufacturing high quality air suspension components for the aftermarket, Arnott says it is “the technical expert when it comes to air suspension systems.”
Arnott states that its products are produced with high-quality, OE components offering exact form, fit and function, with each product extensively tested in its American and European facilities and custom-tuned to suit the specific vehicle make and model before being produced.

For more information, visit www.arnottinc.com